Így nincs szükség csavarokra vagy szegecsekre, így a panelek tiszta és zökkenőmentes építészeti megjelenést nyújtanak.
TWEHA SyntheticPrimer
Special surface pre-treatment for synthetic supporting structures and polymer-based surfaces
TWEHA SyntheticPrimer is a specially developed surface pre-treatment for synthetic supporting structures and supporting surfaces with a synthetic or polymer-based finish, where direct adhesive bonding may be limited by a relatively low surface energy.
Many plastics and polymer-based surface finishes have surface characteristics that make reliable wetting and adhesion difficult. TWEHA SyntheticPrimer modifies the bonding surface and creates a smooth, consistent and stable interface onto which the TWEHA adhesive can be applied.
TWEHA SyntheticPrimer is particularly intended for supporting structures manufactured from synthetic materials or provided with a plastic-related surface. Certain powder coatings are also considered polymer-based surfaces from an adhesive-bonding perspective and may therefore require this type of pre-treatment. Due to the large variation in plastic and coating formulations, durable adhesion must always be verified by testing before use.
TWEHA SyntheticPrimer should be regarded as a surface pre-treatment rather than a conventional adhesion primer. Its purpose is to modify and homogenize the synthetic bonding surface so that a controlled interface for the TWEHA adhesive is created.
Before application, the surface must be dry, clean and free from dust, grease and other contamination. Thoroughly clean and degrease the bonding area with TWEHA Cleaner+ and allow the cleaner to evaporate completely.
Shake TWEHA SyntheticPrimer thoroughly before use and apply one thin, continuous layer using a suitable brush or fine-structure roller. Process only the quantity required and keep the container closed as much as possible during use.
Allow TWEHA SyntheticPrimer to dry completely. Bonding with the appropriate TWEHA adhesive can commence after a minimum of approximately 30 minutes, subject to the applicable environmental conditions and Instructions for Use.
Because plastics, composites and polymer coatings can differ significantly in chemical composition and surface energy, the use of TWEHA SyntheticPrimer does not in itself guarantee durable adhesion. The complete combination of supporting material, surface finish, SyntheticPrimer and TWEHA adhesive must always be assessed by means of an appropriate adhesion and durability test before application. TWEHA specifically requires testing for critical low-surface-energy and powder-coated surfaces.
Always refer to the applicable TWEHA Technical Data Sheet, Instructions for Use and the current list of Tested & Approved
Can
1 ltr
A teljesítmény és a hatékonyság jegyében tervezve
Megbízható ragasztás érdekében kifejlesztve
TWEHA SyntheticPrimer creates improved bonding conditions on difficult synthetic surfaces:
01
Developed for Synthetic Surfaces
Specifically developed for synthetic and polymer-based surfaces within TWEHA Bonding Systems.
02
Suitable for Selected Substrates
Particularly suitable for synthetic supporting structures, selected low-surface-energy substrates and tested powder-coated surfaces.
03
Improved Bonding Interface
Creates a smooth, consistent surface and promotes better wetting by the TWEHA adhesive.
04
Stable Intermediate Layer
Improves conditions for adhesive application where direct primerless bonding cannot be demonstrated.
05
Fast and Economical Application
Easy to apply, fast-drying and requires only one thin, continuous layer.
TWEHA SyntheticPrimer is particularly suitable for:
TWEHA SyntheticPrimer is particularly suitable for synthetic supporting structures, polymer-based supporting profiles, and plastic or plastic-related bonding surfaces, including selected composite supporting materials with a synthetic bonding surface and selected powder-coated supporting structures. It is designed for low surface energy substrates where direct adhesive bonding is insufficient, and is used for the preparation of difficult synthetic surfaces before application of a TWEHA adhesive. Suitable for ventilated and rainscreen façade constructions with synthetic supporting components, it is the product of choice for professional façade applications where a controlled adhesive interface is required.
TWEHA SyntheticPrimer is intended for the supporting structure or bonding substrate. It is not intended as a general primer for the rear surface of façade panels and must therefore not be applied to the back of the cladding panel unless specifically tested and approved by TWEHA for that application.
Teljes körű ragasztási rendszer
A TWEHA összes terméke a Tweha Bonding System részét képezi. A rendszer helyes alkalmazásához mindig vegye figyelembe a műszaki adatlapokat és a jóváhagyott aljzatlistákat.
English (UK) 
Nederlands 
Dansk 
Русский 
Polski 
Slovenčina 
Български 
Română 
Ελληνικά 
Eesti 
Svenska 
Norsk bokmål 
Italiano 
Latviešu valoda 
Lietuvių kalba 
Español 
Suomi 
Српски језик 
Čeština 
Deutsch 
العربية 
Bosanski 
ქართული Műszaki kérdések
Itt találhat gyors válaszokat a StoneMate-tel kapcsolatos gyakori technikai kérdésekre.
SyntheticPrimer is a surface treatment for selected low-surface-energy synthetic or coated materials where additional adhesion improvement is required.
No. Powder coatings vary greatly in composition and adhesion, so applying SyntheticPrimer alone does not constitute technical approval.
Not as a standard TWEHA solution. Where bonding to the aluminium flange is required, the powder coating must be completely removed unless the specific system has been tested and approved.
No. The surface must still be dry, clean and grease-free before SyntheticPrimer is applied.
Surface energy, coating chemistry and coating adhesion can differ significantly, so durable adhesion must be verified on the actual material.
Hatékonyabb, gazdaságosabb
A hagyományos mechanikus rögzítőrendszerekhez képest a TWEHA ragasztórendszerek akár 40%-vel is csökkenthetik a szerelési költségeket.
A gyorsabb szerelés, a kevesebb alkatrész és a láthatatlan rögzítések mind gazdasági, mind esztétikai előnyökkel járnak.
Készen állsz a korlátok nélküli építkezésre?
Fedezze fel, hogyan teszi termékünk lehetővé a homlokzatok tisztább, gyorsabb és hatékonyabb felszerelését.
English 
Dutch 
Danish 
Russian 
Polish 
Slovak 
Bulgarian 
Romanian 
Greek 
Estonian 
Swedish 
Norwegian 
Italian 
Latvian 
Hungarian 
Lithuanian 
Spanish 
Finnish 
Serbian 
Czech 
German 
Arabic 
Bosnian 
Georgian