Võimaldab loobuda kruvide ja neetide kasutamisest, tänu millele säilitavad paneelid puhtad ja ühtlased arhitektuurilised jooned.
TWEHA sünteetiline krunt
Special surface pre-treatment for synthetic supporting structures and polymer-based surfaces
TWEHA SyntheticPrimer on spetsiaalselt välja töötatud pinnatöötlusvahend sünteetilistele kandekonstruktsioonidele ja sünteetilise või polümeeripõhise viimistlusega kandepindadele, kus otsene liimimine võib olla piiratud suhteliselt madala pindenergia tõttu.
Paljudel plastidel ja polümeeripõhistel pinnakattematerjalidel on sellised pinnakarakteristikud, mis raskendavad usaldusväärset niisutamist ja haardumist. TWEHA SyntheticPrimer muudab liimimispinda ning loob sileda, ühtlase ja stabiilse liidese, millele saab kanda TWEHA liimi.
TWEHA SyntheticPrimer on mõeldud eelkõige sünteetilistest materjalidest valmistatud või plastiga seotud pinnaga kandekonstruktsioonidele. Teatavaid pulbervärve peetakse ka polümeeripõhisteks pindadeks kleepumise seisukohast ning seetõttu võivad need vajada sellist eeltöötlust. Kuna plastide ja värvikoostiste vahel on suuri erinevusi, tuleb püsiva kleepumise tagamine enne kasutamist alati katsetustega kontrollida.
TWEHA SyntheticPrimer should be regarded as a surface pre-treatment rather than a conventional adhesion primer. Its purpose is to modify and homogenize the synthetic bonding surface so that a controlled interface for the TWEHA adhesive is created.
Before application, the surface must be dry, clean and free from dust, grease and other contamination. Thoroughly clean and degrease the bonding area with TWEHA Cleaner+ and allow the cleaner to evaporate completely.
Shake TWEHA SyntheticPrimer thoroughly before use and apply one thin, continuous layer using a suitable brush or fine-structure roller. Process only the quantity required and keep the container closed as much as possible during use.
Allow TWEHA SyntheticPrimer to dry completely. Bonding with the appropriate TWEHA adhesive can commence after a minimum of approximately 30 minutes, subject to the applicable environmental conditions and Instructions for Use.
Because plastics, composites and polymer coatings can differ significantly in chemical composition and surface energy, the use of TWEHA SyntheticPrimer does not in itself guarantee durable adhesion. The complete combination of supporting material, surface finish, SyntheticPrimer and TWEHA adhesive must always be assessed by means of an appropriate adhesion and durability test before application. TWEHA specifically requires testing for critical low-surface-energy and powder-coated surfaces.
Always refer to the applicable TWEHA Technical Data Sheet, Instructions for Use and the current list of Tested & Approved
Kas
1 liiter
Loodud jõudluse ja tõhususe nimel
Loodud usaldusväärseks liimimiseks
TWEHA SyntheticPrimer creates improved bonding conditions on difficult synthetic surfaces:
01
Developed for Synthetic Surfaces
Specifically developed for synthetic and polymer-based surfaces within TWEHA Bonding Systems.
02
Suitable for Selected Substrates
Particularly suitable for synthetic supporting structures, selected low-surface-energy substrates and tested powder-coated surfaces.
03
Improved Bonding Interface
Creates a smooth, consistent surface and promotes better wetting by the TWEHA adhesive.
04
Stable Intermediate Layer
Improves conditions for adhesive application where direct primerless bonding cannot be demonstrated.
05
Fast and Economical Application
Easy to apply, fast-drying and requires only one thin, continuous layer.
TWEHA SyntheticPrimer is particularly suitable for:
TWEHA SyntheticPrimer is particularly suitable for synthetic supporting structures, polymer-based supporting profiles, and plastic or plastic-related bonding surfaces, including selected composite supporting materials with a synthetic bonding surface and selected powder-coated supporting structures. It is designed for low surface energy substrates where direct adhesive bonding is insufficient, and is used for the preparation of difficult synthetic surfaces before application of a TWEHA adhesive. Suitable for ventilated and rainscreen façade constructions with synthetic supporting components, it is the product of choice for professional façade applications where a controlled adhesive interface is required.
TWEHA SyntheticPrimer is intended for the supporting structure or bonding substrate. It is not intended as a general primer for the rear surface of façade panels and must therefore not be applied to the back of the cladding panel unless specifically tested and approved by TWEHA for that application.
Täielik liimimissüsteem
Kõik TWEHA tooted kuuluvad Tweha Bonding Systemi. Süsteemi õigeks kasutamiseks tutvuge alati tehniliste andmelehtede ja heakskiidetud alusmaterjalide nimekirjadega.
Tehniline dokumentatsioon
Tehnilised küsimused
Leia kiired vastused StoneMate’iga seotud tavapärastele tehnilistele küsimustele.
SyntheticPrimer is a surface treatment for selected low-surface-energy synthetic or coated materials where additional adhesion improvement is required.
No. Powder coatings vary greatly in composition and adhesion, so applying SyntheticPrimer alone does not constitute technical approval.
Not as a standard TWEHA solution. Where bonding to the aluminium flange is required, the powder coating must be completely removed unless the specific system has been tested and approved.
No. The surface must still be dry, clean and grease-free before SyntheticPrimer is applied.
Surface energy, coating chemistry and coating adhesion can differ significantly, so durable adhesion must be verified on the actual material.
Tõhusam, ökonoomsem
Võrreldes traditsiooniliste mehaaniliste kinnitussüsteemidega võimaldavad TWEHA liimimissüsteemid vähendada paigalduskulusid kuni 40% võrra.
Kiirem paigaldamine, vähem komponente ja nähtamatud kinnitused pakuvad nii majanduslikke kui ka esteetilisi eeliseid.
Kas oled valmis piirideta ehitama?
Avastage, kuidas meie toode võimaldab fassaadide paigaldamist puhtamalt, kiiremini ja tõhusamalt.